Specials
Suspension
Recovery
Armor/Bumpers
Builds
CB's
Jeep Parts


12-50-010
Ricochet Rocker™ protection can be used alone or in combination with Crusher Corners™. The two body armor pieces fit together at the rear flare area. Used together, Ricochet Rockers' and Crusher Corners™ form the ultimate protection, guarding your Jeep's body from the front wheel well to the tailgate. Ricochet Rockers™ are secured with counter sunk 3/8" stainless hardware, supplied in the kit with detailed installation instructions.
Ricochet Rockers™ have a distinguishing 5" dimpled plate that acts as a step and a stout reinforcement for the slider. This makes the Ricochet Rocker™ protection a very effective armor addition and an effective pivot for getting into your rock chariot. Jeep TJ,YJ and CJ7 have three dimples, Unlimited and CJ8 have four. With the dimple protrusions pointing upward, they give the extra benefit of increased foot traction when entering or exiting the vehicle, even with boots covered with snow or mud
Ricochet Rockers™ are further reinforced with additional bracing below the dimpled step. The dual tube support and slider bar is constructed of 1.5" DOM tubing, the step and corner gussets are CNC laser cut from 3/16" steel plate, and brake-formed to act as their own gusset for strength and a clean appearance. Everything is professionally welded and comes to you ready to paint and bolt on.
NOTE: When installing CJ-8 Ricochet Rockers in conjunction with Poison Spyder (or other manufacturers) Tube Fenders with Tube Flares, you will need to trim a few inches of material from the forward edge (trimming is not needed when used with Tube Fenders without Tube Flares). You will want to test-fit and trim BEFORE YOU PAINT OR POWDER COAT.
$499.00

 


13-50-050
Ricochet Rocker™ protection can be used alone or in combination with Crusher Corners™. The two body armor pieces fit together at the rear flare area. Used together, Ricochet Rockers' and Crusher Corners™ form the ultimate protection, guarding your Jeep's body from the front wheel well to the tailgate. Ricochet Rockers™ are secured with counter sunk 3/8" stainless hardware, supplied in the kit with detailed installation instructions.
Ricochet Rockers™ have a distinguishing 5" dimpled plate that acts as a step and a stout reinforcement for the slider. This makes the Ricochet Rocker™ protection a very effective armor addition and an effective pivot for getting into your rock chariot. Jeep TJ,YJ and CJ7 have three dimples, Unlimited and CJ8 have four. With the dimple protrusions pointing upward, they give the extra benefit of increased foot traction when entering or exiting the vehicle, even with boots covered with snow or mud
Ricochet Rockers™ are further reinforced with additional bracing below the dimpled step. The dual tube support and slider bar is constructed of 1.5" DOM tubing, the step and corner gussets are CNC laser cut from 3/16" steel plate, and brake-formed to act as their own gusset for strength and a clean appearance. Everything is professionally welded and comes to you ready to paint and bolt on.
$468.00

 


11-50-010
Ricochet Rocker™ protection can be used alone or in combination with Crusher Corners™. The two body armor pieces fit together at the rear flare area. Used together, Ricochet Rockers' and Crusher Corners™ form the ultimate protection, guarding your Jeep's body from the front wheel well to the tailgate. Ricochet Rockers™ are secured with counter sunk 3/8" stainless hardware, supplied in the kit with detailed installation instructions.
Ricochet Rockers™ have a distinguishing 5" dimpled plate that acts as a step and a stout reinforcement for the slider. This makes the Ricochet Rocker™ protection a very effective armor addition and an effective pivot for getting into your rock chariot. Jeep TJ,YJ and CJ7 have three dimples, Unlimited and CJ8 have four. With the dimple protrusions pointing upward, they give the extra benefit of increased foot traction when entering or exiting the vehicle, even with boots covered with snow or mud
Ricochet Rockers™ are further reinforced with additional bracing below the dimpled step. The dual tube support and slider bar is constructed of 1.5" DOM tubing, the step and corner gussets are CNC laser cut from 3/16" steel plate, and brake-formed to act as their own gusset for strength and a clean appearance. Everything is professionally welded and comes to you ready to paint and bolt on.
This specific part number is for use on CJ-7's where the stock front and rear fender flares are being retained, as they are cut to fit around the flares at either end. This specific part number is also compatible with our CJ-7 Crusher Corners in the STOCK configuration. It is NOT compatible with "Standard" Crusher Corners—in that case choose our YJ/CJ-7 Ricochet Rockers with TJ Wheel Opening.
$468.00

 


12-08-020
Poison Spyder Rocker Knockers™ protect your rocker panels by cladding them in rugged, high strength 3/16" plate steel armor. Rocker Knockers™ are manufactured to hug the lines of your Jeep's rocker panels perfectly, forming a glove-fit with virtually no loss of valuable ground clearance. Specifically engineered for most Jeep CJ, YJ, TJ and LJ models, Rocker Knockers™ are CNC laser cut from high strength 3/16" plate steel, and precisiion brake-formed for a perfect fit. Bolt holes are countersunk for the included stainless steel flat head hardware, which yields a flat, unobstructed surface to slide over obstacles. All mounting hardware is included as well as detailed installation instructions. Poison Spyder Rocker Knockers™ bolt to your Jeep's body in key areas, and interface with strenghtened areas of the underside of the tub such as body mounts, strengthening ribs, etc. Because they mount to the body itself, there is no resulting gap or misalignment when a body lift is installed.
For added side protection on the trail, these Rocker Knockers™ come with a tubular Slider. The Slider is crafted of high strength DOM structural tubing, welded to the Rocker Knocker™ with additional DOM tube spacers. The result is a combination of rocker panel protection and a tubular slider to keep your rig's bodysides a few precious inches away from taller rocks and trees. The Slider may also become an integral part of your driving strategy, as it may be useful to pivot the vehicle around obstacles while searching for traction. It also serves as a short entry step, assisting entry and egress.
NOTE: When installing CJ-8 Rocker Knockers in conjunction with Poison Spyder (or other manufacturers) Tube Fenders with Tube Flares, you will need to trim a few inches of material from the forward edge (trimming is not needed when used with Tube Fenders without Tube Flares). You will want to test-fit and trim BEFORE YOU PAINT OR POWDER COAT.
$405.00

 


10-08-020
Poison Spyder Rocker Knockers™ protect your rocker panels by cladding them in rugged, high strength 3/16" plate steel armor. Rocker Knockers™ are manufactured to hug the lines of your Jeep's rocker panels perfectly, forming a glove-fit with virtually no loss of valuable ground clearance. Specifically engineered for most Jeep CJ, YJ, TJ and LJ models, Rocker Knockers™ are CNC laser cut from high strength 3/16" plate steel, and precisiion brake-formed for a perfect fit. Bolt holes are countersunk for the included stainless steel flat head hardware, which yields a flat, unobstructed surface to slide over obstacles. All mounting hardware is included as well as detailed installation instructions. Poison Spyder Rocker Knockers™ bolt to your Jeep's body in key areas, and interface with strenghtened areas of the underside of the tub such as body mounts, strenthening ribs, etc. Because they mount to the body itself, there is no resulting gap or misalignment when a body lift is installed.
For added side protection on the trail, these Rocker Knockers™ come with a tubular Slider. The Slider is crafted of high strength DOM structural tubing, welded to the Rocker Knocker™ with additional DOM tube spacers. The result is a combination of rocker panel protection and a tubular slider to keep your rig's bodysides a few precious inches away from taller rocks and trees. The Slider may also become an integral part of your driving strategy, as it may be useful to pivot the vehicle around obstacles while searching for traction. It also serves as a short entry step, assisting entry and egress.
$365.00

 


13-08-050
Poison Spyder Rocker Knockers™ protect your rocker panels by cladding them in rugged, high strength 3/16" plate steel armor. Rocker Knockers™ are manufactured to hug the lines of your Jeep's rocker panels perfectly, forming a glove-fit with virtually no loss of valuable ground clearance. Specifically engineered for most Jeep CJ, YJ, TJ and LJ models, Rocker Knockers™ are CNC laser cut from high strength 3/16" plate steel, and precisiion brake-formed for a perfect fit. Bolt holes are countersunk for the included stainless steel flat head hardware, which yields a flat, unobstructed surface to slide over obstacles. All mounting hardware is included as well as detailed installation instructions. Poison Spyder Rocker Knockers™ bolt to your Jeep's body in key areas, and interface with strenghtened areas of the underside of the tub such as body mounts, strenthening ribs, etc. Because they mount to the body itself, there is no resulting gap or misalignment when a body lift is installed.
For added side protection on the trail, these Rocker Knockers™ come with a tubular Slider. The Slider is crafted of high strength DOM structural tubing, welded to the Rocker Knocker™ with additional DOM tube spacers. The result is a combination of rocker panel protection and a tubular slider to keep your rig's bodysides a few precious inches away from taller rocks and trees. The Slider may also become an integral part of your driving strategy, as it may be useful to pivot the vehicle around obstacles while searching for traction. It also serves as a short entry step, assisting entry and egress.
$365.00

 


11-08-020
Poison Spyder Rocker Knockers™ protect your rocker panels by cladding them in rugged, high strength 3/16" plate steel armor. Rocker Knockers™ are manufactured to hug the lines of your Jeep's rocker panels perfectly, forming a glove-fit with virtually no loss of valuable ground clearance. Specifically engineered for most Jeep CJ, YJ, TJ and LJ models, Rocker Knockers™ are CNC laser cut from high strength 3/16" plate steel, and precisiion brake-formed for a perfect fit. Bolt holes are countersunk for the included stainless steel flat head hardware, which yields a flat, unobstructed surface to slide over obstacles. All mounting hardware is included as well as detailed installation instructions. Poison Spyder Rocker Knockers™ bolt to your Jeep's body in key areas, and interface with strenghtened areas of the underside of the tub such as body mounts, strenthening ribs, etc. Because they mount to the body itself, there is no resulting gap or misalignment when a body lift is installed.
For added side protection on the trail, these Rocker Knockers™ come with a tubular Slider. The Slider is crafted of high strength DOM structural tubing, welded to the Rocker Knocker™ with additional DOM tube spacers. The result is a combination of rocker panel protection and a tubular slider to keep your rig's bodysides a few precious inches away from taller rocks and trees. The Slider may also become an integral part of your driving strategy, as it may be useful to pivot the vehicle around obstacles while searching for traction. It also serves as a short entry step, assisting entry and egress.
This specific part number is for use on CJ-7's where the stock front and rear fender flares are being retained, as they are cut to fit around the flares at either end. This specific part number is also compatible with our CJ-7 Crusher Corners in the STOCK configuration. It is NOT compatible with "Standard" Crusher Corners—in that case choose our YJ/CJ-7 Rocker Knockers with TJ Wheel Opening.
$365.00

 


12-08-010
Poison Spyder Rocker Knockers™ protect your rocker panels by cladding them in rugged, high strength 3/16" plate steel armor. Rocker Knockers™ are manufactured to hug the lines of your Jeep's rocker panels perfectly, forming a glove-fit with virtually no loss of valuable ground clearance. Specifically engineered for most Jeep CJ, YJ, TJ and LJ models, Rocker Knockers™ are CNC laser cut from high strength 3/16" plate steel, and precisiion brake-formed for a perfect fit. Bolt holes are countersunk for the included stainless steel flat head hardware, which yields a flat, unobstructed surface to slide over obstacles. All mounting hardware is included as well as detailed installation instructions. Poison Spyder Rocker Knockers™ bolt to your Jeep's body in key areas, and interface with strenghtened areas of the underside of the tub such as body mounts, strenthening ribs, etc. Because they mount to the body itself, there is no resulting gap or misalignment when a body lift is installed.
NOTE: When installing CJ-8 Rocker Knockers in conjunction with Poison Spyder (or other manufacturers) Tube Fenders with Tube Flares, you will need to trim a few inches of material from the forward edge (trimming is not needed when used with Tube Fenders without Tube Flares). You will want to test-fit and trim BEFORE YOU PAINT OR POWDER COAT.
$315.00

 


13-08-040
Poison Spyder Rocker Knockers™ protect your rocker panels by cladding them in rugged, high strength 3/16" plate steel armor. Rocker Knockers™ are manufactured to hug the lines of your Jeep's rocker panels perfectly, forming a glove-fit with virtually no loss of valuable ground clearance. Specifically engineered for most Jeep CJ, YJ, TJ and LJ models, Rocker Knockers™ are CNC laser cut from high strength 3/16" plate steel, and precisiion brake-formed for a perfect fit. Bolt holes are countersunk for the included stainless steel flat head hardware, which yields a flat, unobstructed surface to slide over obstacles. All mounting hardware is included as well as detailed installation instructions. Poison Spyder Rocker Knockers™ bolt to your Jeep's body in key areas, and interface with strenghtened areas of the underside of the tub such as body mounts, strenthening ribs, etc. Because they mount to the body itself, there is no resulting gap or misalignment when a body lift is installed.
$275.00

 


11-08-010
Poison Spyder Rocker Knockers™ protect your rocker panels by cladding them in rugged, high strength 3/16" plate steel armor. Rocker Knockers™ are manufactured to hug the lines of your Jeep's rocker panels perfectly, forming a glove-fit with virtually no loss of valuable ground clearance. Specifically engineered for most Jeep CJ, YJ, TJ and LJ models, Rocker Knockers™ are CNC laser cut from high strength 3/16" plate steel, and precision brake-formed for a perfect fit. Bolt holes are countersunk for the included stainless steel flat head hardware, which yields a flat, unobstructed surface to slide over obstacles. All mounting hardware is included as well as detailed installation instructions. Poison Spyder Rocker Knockers™ bolt to your Jeep's body in key areas, and interface with strengthened areas of the underside of the tub such as body mounts, strengthening ribs, etc. Because they mount to the body itself, there is no resulting gap or misalignment when a body lift is installed.
This specific part number is for use on CJ-7's where the stock front and rear fender flares are being retained, as they are cut to fit around the flares at either end. This specific part number is also compatible with our CJ-7 Crusher Corners in the STOCK configuration. It is NOT compatible with "Standard" Crusher Corners—in that case choose our YJ/CJ-7 Rocker Knockers with TJ Wheel Opening.
$275.00