Specials
Suspension
Recovery
Armor/Bumpers
Builds
CB's
Jeep Parts


15-50-050
Ricochet Rocker™ protection can be used alone or in combination with Crusher Corners™. The two body armor pieces fit together at the rear flare area. Used together, Ricochet Rockers' and Crusher Corners™ form the ultimate protection, guarding your Jeep's body from the front wheel well to the tailgate. Ricochet Rockers™ are secured with counter sunk 3/8" stainless hardware, supplied in the kit with detailed installation instructions.
Ricochet Rockers™ have a distinguishing 5" dimpled plate that acts as a step and a stout reinforcement for the slider. This makes the Ricochet Rocker™ protection a very effective armor addition and an effective pivot for getting into your rock chariot. Jeep TJ,YJ and CJ7 have three dimples, Unlimited and CJ8 have four. With the dimple protrusions pointing upward, they give the extra benefit of increased foot traction when entering or exiting the vehicle, even with boots covered with snow or mud
Ricochet Rockers™ are further reinforced with additional bracing below the dimpled step. The dual tube support and slider bar is constructed of 1.5" DOM tubing, the step and corner gussets are CNC laser cut from 3/16" steel plate, and brake-formed to act as their own gusset for strength and a clean appearance. Everything is professionally welded and comes to you ready to paint and bolt on.
$499.00

 


14-50-050
Ricochet Rocker™ protection can be used alone or in combination with Crusher Corners™. The two body armor pieces fit together at the rear flare area. Used together, Ricochet Rockers' and Crusher Corners™ form the ultimate protection, guarding your Jeep's body from the front wheel well to the tailgate. Ricochet Rockers™ are secured with counter sunk 3/8" stainless hardware, supplied in the kit with detailed installation instructions.
Ricochet Rockers™ have a distinguishing 5" dimpled plate that acts as a step and a stout reinforcement for the slider. This makes the Ricochet Rocker™ protection a very effective armor addition and an effective pivot for getting into your rock chariot. Jeep TJ,YJ and CJ7 have three dimples, Unlimited and CJ8 have four. With the dimple protrusions pointing upward, they give the extra benefit of increased foot traction when entering or exiting the vehicle, even with boots covered with snow or mud
Ricochet Rockers™ are further reinforced with additional bracing below the dimpled step. The dual tube support and slider bar is constructed of 1.5" DOM tubing, the step and corner gussets are CNC laser cut from 3/16" steel plate, and brake-formed to act as their own gusset for strength and a clean appearance. Everything is professionally welded and comes to you ready to paint and bolt on.
$468.00

 


15-08-060
Poison Spyder Rocker Knockers™ protect your rocker panels by cladding them in rugged, high strength 3/16" plate steel armor. Rocker Knockers™ are manufactured to hug the lines of your Jeep's rocker panels perfectly, forming a glove-fit with virtually no loss of valuable ground clearance. Specifically engineered for most Jeep CJ, YJ, TJ and LJ models, Rocker Knockers™ are CNC laser cut from high strength 3/16" plate steel, and precisiion brake-formed for a perfect fit. Bolt holes are countersunk for the included stainless steel flat head hardware, which yields a flat, unobstructed surface to slide over obstacles. All mounting hardware is included as well as detailed installation instructions. Poison Spyder Rocker Knockers™ bolt to your Jeep's body in key areas, and interface with strenghtened areas of the underside of the tub such as body mounts, strenthening ribs, etc. Because they mount to the body itself, there is no resulting gap or misalignment when a body lift is installed.
For added side protection on the trail, Rocker Knockers™ can be ordered with the optional tubular Slider. The Slider is crafted of high strength DOM structural tubing, welded to the Rocker Knocker™ with additional DOM tube spacers. The result is a combination of rocker panel protection and a tubular slider to keep your rig's bodysides a few precious inches away from taller rocks and trees. The Slider may also become an integral part of your driving strategy, as it may be useful to pivot the vehicle around obstacles while searching for traction. It also serves as a short entry step, assisting entry and egress. For those who want a more purpose-built entry step, check out Poison Spyder's Ricochet Rockers™.
$405.00

 


14-08-060
Poison Spyder Rocker Knockers™ protect your rocker panels by cladding them in rugged, high strength 3/16" plate steel armor. Rocker Knockers™ are manufactured to hug the lines of your Jeep's rocker panels perfectly, forming a glove-fit with virtually no loss of valuable ground clearance. Specifically engineered for most Jeep CJ, YJ, TJ and LJ models, Rocker Knockers™ are CNC laser cut from high strength 3/16" plate steel, and precisiion brake-formed for a perfect fit. Bolt holes are countersunk for the included stainless steel flat head hardware, which yields a flat, unobstructed surface to slide over obstacles. All mounting hardware is included as well as detailed installation instructions. Poison Spyder Rocker Knockers™ bolt to your Jeep's body in key areas, and interface with strenghtened areas of the underside of the tub such as body mounts, strenthening ribs, etc. Because they mount to the body itself, there is no resulting gap or misalignment when a body lift is installed.
$365.00

 


15-08-050
Poison Spyder Rocker Knockers™ protect your rocker panels by cladding them in rugged, high strength 3/16" plate steel armor. Rocker Knockers™ are manufactured to hug the lines of your Jeep's rocker panels perfectly, forming a glove-fit with virtually no loss of valuable ground clearance. Specifically engineered for most Jeep CJ, YJ, TJ and LJ models, Rocker Knockers™ are CNC laser cut from high strength 3/16" plate steel, and precisiion brake-formed for a perfect fit. Bolt holes are countersunk for the included stainless steel flat head hardware, which yields a flat, unobstructed surface to slide over obstacles. All mounting hardware is included as well as detailed installation instructions. Poison Spyder Rocker Knockers™ bolt to your Jeep's body in key areas, and interface with strenghtened areas of the underside of the tub such as body mounts, strenthening ribs, etc. Because they mount to the body itself, there is no resulting gap or misalignment when a body lift is installed.
For added side protection on the trail, Rocker Knockers™ can be ordered with the optional tubular Slider. The Slider is crafted of high strength DOM structural tubing, welded to the Rocker Knocker™ with additional DOM tube spacers. The result is a combination of rocker panel protection and a tubular slider to keep your rig's bodysides a few precious inches away from taller rocks and trees. The Slider may also become an integral part of your driving strategy, as it may be useful to pivot the vehicle around obstacles while searching for traction. It also serves as a short entry step, assisting entry and egress. For those who want a more purpose-built entry step, check out Poison Spyder's Ricochet Rockers™.
$315.00

 


14-08-050
Poison Spyder Rocker Knockers™ protect your rocker panels by cladding them in rugged, high strength 3/16" plate steel armor. Rocker Knockers™ are manufactured to hug the lines of your Jeep's rocker panels perfectly, forming a glove-fit with virtually no loss of valuable ground clearance. Specifically engineered for most Jeep CJ, YJ, TJ and LJ models, Rocker Knockers™ are CNC laser cut from high strength 3/16" plate steel, and precisiion brake-formed for a perfect fit. Bolt holes are countersunk for the included stainless steel flat head hardware, which yields a flat, unobstructed surface to slide over obstacles. All mounting hardware is included as well as detailed installation instructions. Poison Spyder Rocker Knockers™ bolt to your Jeep's body in key areas, and interface with strenghtened areas of the underside of the tub such as body mounts, strenthening ribs, etc. Because they mount to the body itself, there is no resulting gap or misalignment when a body lift is installed.
$275.00

 


DIY-50-020
The DIY Rico Step™ Kit  from Poison Spyder allows the do-it-yourselfer to add a heavy duty rub rail and entry step to the stock Jeep JK Rubicon rocker rails, Poison Spyder Rocker Knockers™ or other aftermarket plate steel rocker armor. The components provided in the kit are similar to Poison Spyder's "Ricochet Rockers", hence the name of the kit. The kit includes DOM tube rub rails, Rico Steps and end gussets. The DOM tube pieces are CNC bent and pre-notched, ready to weld on. The Rico Steps and gussets are laser cut from 3/16 plate steel. The steps are brake-formed to provide extra strength and reverse-dimpled for foot traction. The main tubes measure 45.25" long and the kit was designed specifically for the TJ, YJ and CJ-7, but might possibly be used on other vehicles if it fits.  Requires welding.
$175.00

 


DIY-08-030
The DIY Slider Tube Kit  from Poison Spyder allows the do-it-yourselfer to add a rugged DOM tube slider to Poison Spyder Rocker Knockers™ or other aftermarket plate steel rocker armor. The kit includes the slider tubes as well as the short tube supports to brace the center of the tube against the rocker, to do both sides of the Jeep.  The DOM slider tube pieces are CNC bent and pre-notched to mount at an angle, as with our ready-built Rocker Knockers™ with Sliders. The main tubes measure 53.75" long and the kit was designed specifically for the Jeep LJ and CJ-8, but might possibly be used on other vehicles if it fits.  Requires welding.
$119.00

 


DIY-08-010
The DIY Slider Tube Kit  from Poison Spyder allows the do-it-yourselfer to add a rugged DOM tube slider to Poison Spyder Rocker Knockers™ or other aftermarket plate steel rocker armor. The kit includes the slider tubes as well as the short tube supports to brace the center of the tube against the rocker, to do both sides of the Jeep.  The DOM slider tube pieces are CNC bent and pre-notched to mount at an angle, as with our ready-built Rocker Knockers™ with Sliders. The main tubes measure 39.5" long and the kit was designed specifically for the Jeep CJ-5, but might possibly be used on other vehicles if it fits.  Requires welding.
$109.00

 


DIY-08-020
The DIY Slider Tube Kit  from Poison Spyder allows the do-it-yourselfer to add a rugged DOM tube slider to Poison Spyder Rocker Knockers™ or other aftermarket plate steel rocker armor. The kit includes the slider tubes as well as the short tube supports to brace the center of the tube against the rocker, to do both sides of the Jeep.  The DOM slider tube pieces are CNC bent and pre-notched to mount at an angle, as with our ready-built Rocker Knockers™ with Sliders. The main tubes measure 44.25" long and the kit was designed specifically for the Jeep TJ, YJ and CJ-7, but might possibly be used on other vehicles if it fits.  Requires welding.
$109.00